Installation and User Manual Infinity 32e and HD70eInfinity 32e and HD70e Continuous Flow Water Heater Important. Read these instructions carefully b
10TECHNICAL DETAILS Infinity Model Infinity 32e HD70eUnits Installation ExternalExternalNat Gas Press Low 1.8 1.8 mbarNat Gas Press High 7.4 7.4
11Congratulations on purchasing the Technologically Advanced, Temperature Controlled,Rinnai Hot Water System. • The Rinnai Infinity 32e and HD70e NEVE
12Excessively hot water is dangerous, especially for young children and the infirm. Thewater heater allows you to control the temperature of your hot
13IMPORTANT INFORMATION Always check water temperature beforeuse.Refer to warning about hot water onpage 12 for important safety information. Hot wate
Te14 Rinnai Infinity and HD products have no pilot light and when installed without Temperature Controllers, the appliance will operate automatically
15 TEMPERATURE CONTROLS - GENERAL When deciding on the best position for the temperature controls, the following points should be taken into account.
16 TEMPERATURE CONTROLS - INSTALLATION Universal Temperature Controller MC-91-1A 1. Determine the most suitable position for the temperature control
17 TEMPERATURE CONTROLS - INSTALLATION Connecting One or Two Controllers 1. Isolate the power supply. 2. Remove the front cover from the Appliance (4
18 TEMPERATURE CONTROLS The purpose of a Temperature Controller is to enable the user to have complete control over the hot water supply. Used correct
19 Remote temperature controllers are a feature that provides control over the water temperature. Rinnai Infinity and HD water heaters can be operate
2RINNAI UK WARRANTYAs the purchaser of this high quality Rinnai Water Heater you are provided with the following conditional guarantee. Defini
20 TEMPERATURE CONTROLS - OPERATING Using 1 Universal Temperature Controller. Press the On/Off button on the temperature controller. The ON
21 Using 2 or more Universal Temperature Controllers. Switching the system ON. Using hot water. Bathroom temperatures
22 Using 4 Universal Temperature Controllers. You will need to activate the fourth controller. STEP 1: STEP 2:
23 Using High Temperature Display Controllers. You will need to program the Master controller if you want to display and use temperatures over 500C.
24 Note To turn off your hot water system. Additional safety features. During normal operation the system i
25 TEMPERATURE CONTROLS - INFORMATION Do not push the On/Off button on the Master controller after transferring priority of temperature selection to a
26 TESTING 1. Purge gas, hot water and cold water supply lines before making the final connection of the water heater. Swarf in either the gas
27 GAS PRESSURE SETTING The working gas pressure on the water heater is electronically controlled and factory set. Under normal circumstances it do
28 GAS PRESSURE SETTING 11.Adjust the regulator screw on the modulating valve (fig. 4) as required to the pressure below. 12.Lock the regula
29 DIP SWITCH SETTING Dip Switch Positions Explained OFF ON SW2 1 - Gas Type LEGEND: 2 - Gas Type Black Section indicates 3 - Tem
3CONTENTS Unpacking Rinnai Water Heater.……………………………………………………………Installation Instructions………………………………………………………………………Flue Requirements...………………………………………
30DIP SWITCH SETTING Infinity 32e and HD70e Temperatures - Remotes Connected off on SW2off on SW2off on SW2off on SW2 1 1 1 1
31ERROR MESSAGES Rinnai water heaters have the ability to check their own operation continuously. If a fault occurs, an error code will flash on the D
32 ERROR MESSAGES Troubleshooting without controllers If you have not installed temperature controllers and experience the following symptoms, please
33 RESTARTING THE RINNAI WATER HEATER Following a power cut the heaters should be restarted in this manner. Standard system. Single or multiple water
34 WIRING DIAGRAM THERMAL FUSETHERMISTOR〔OUTGOING WATERTEMP.〕〔HEAT EXCHANGERTEMP.〕THERMISTORDIP SWITCHGas typeTemperature controlWATER FLOWSENSO
35 DIAGNOSTIC POINTS Diagnostic Points- To be read in conjunction with the wiring diagram. COMPONENTSURGE PROTECTORWATER FLOWCONTROL DEVICEBY
36 SPECIFICATION Model………………………………………………..…...………...Infinity 32e and HD70e Installation…………………………………………...………...……. External location only Fue
37 NOTES
38 SERVICE CONTACT UK LTD. 9 Christleton Court Manor Park Runcorn Cheshire WA7 1ST Tel. 01928 531870 Fax. 01928 531880 E-mail. [email protected]
39 COMMISSIONING CHECK LIST For full details - Refer to Installation InstructionsGas supply pipe is purged of foreign matter before connection.For Hot
4UNPACKING RINNAI WATER HEATER • After unpacking the appliance check for damage, if the heater is damaged contact your supplier immediately. Do not i
(V3232W-UK)U245-2085Printed in Japan 2004.11060 00012 39151 0
5IMPORTANT INFORMATION 1. Gas safety (Installation & Use) regulations 1998 are the ‘Rules in force’. In your own interest and that of safety, it i
6General Installation Information. External Installations. The Rinnai Infinity 32e and HD70e are for external mounting only. The unit is classed as a
7INSTALLATION INSTRUCTIONS - CONNECTIONS Water Supply. Where the water supply pressure exceeds 12 bar, an approved pressure reducing device is requir
8DimeJLHHKFInsion Terminal Position Distance A Directly below an opening, air brick, opening windows, etc. 300mm B Above an opening, air brick , op
9DIMENSIONS
Commentaires sur ces manuels