Rinnai 26i Manuel d'utilisateur

Installation and User Manual Infinity 26i and HD50iInfinity 26i and HD50i Continuous Flow Water Heater Important. Read these

10 FLUE REQUIREMENTS - INSTALLING General. The flue must be installed in accordance with: Manufacturers Installation Instructions British Standards

11 DIMENSIONS

12 TECHNICAL DETAILS * Factory Setting ** Minimum operation flow based on temperature setpoint and

13 Congratulations on purchasing the Technologically Advanced, Temperature Controlled, Rinnai Hot Water System. • The Rinnai Infinity 26i and HD

14 Excessively hot water is dangerous, especially for young children and the infirm. The water heater allows you to control the temperature of your

15 IMPORTANT INFORMATION Always check water temperature before use. Refer to warning about hot water on page 14 for important safety inf

16 Rinnai Infinity and HD products have no pilot light and when installed without Temperature Controllers, the appliance will operate automatically

17 TEMPERATURE CONTROLS - GENERAL When deciding on the best position for the temperature controls, the following points should be taken into account.

18 TEMPERATURE CONTROLS - INSTALLATION Universal Temperature Controller MC-91-1A 1. Determine the most suitable position for the temperature contro

19 TEMPERATURE CONTROLS - INSTALLATION Connecting One or Two Controllers 1. Isolate the power supply. 2. Remove the front cover from the Appliance (4

2 RINNAI UK WARRANTY (from Jan 2005) As the purchaser of this high quality Rinnai Water Heater you are provided with the following conditiona

20 TEMPERATURE CONTROLS The purpose of a Temperature Controller is to enable the user to have complete control over the hot water supply. Used corre

21 Remote temperature controllers are a feature that provides control over the water temperature. Rinnai Infinity and HD water heaters can be operat

22 TEMPERATURE CONTROLS - OPERATING Using 1 Universal Temperature Controller. Press the On/Off button on the temperature controller. The ON

23 Using 2 or more Universal Temperature Controllers. Switching the system ON. Using hot water. Bathroom temperatures

24 Using 4 Universal Temperature Controllers. You will need to activate the fourth controller. STEP 1: STEP 2:

25 Using High Temperature Display Controllers. You will need to program the Master controller if you want to display and use temperatures over 500C

26 Note To turn off your hot water system. Additional safety features. During normal operation the system

27 TEMPERATURE CONTROLS - INFORMATION Do not push the On/Off button on the Master controller after transferring priority of temperature selection to

28 TESTING 1. Purge gas, hot water and cold water supply lines before making the final connection of the water heater. Swarf in either the ga

29 GAS PRESSURE SETTING The working gas pressure on the water heater is electronically controlled and factory set. Under normal circumstances it doe

3 Warranty………………………………… Unpacking Rinnai Water Heater………… Installation Instructions…………………… Flue Requirements………………………... Dimensions……………………………

30 GAS PRESSURE SETTING 11. Remove rubber access plug and adjust the regulator screw on the modulating valve (fig. 4) as required to the pressure be

31 DIP SWITCH SETTING Dip Switch Positions Explained OFF ON SW1 1 - Computer Programming LEGEND:

32 DIP SWITCH SETTING Infinity 26i and HD50i Temperatures - With or Without Remotes Connected off on SWI off on SWI off

33 ERROR MESSAGES Rinnai water heaters have the ability to check their own operation continuously. If a fault occurs, an error code will flash on the

34 ERROR MESSAGES Troubleshooting without controllers If you have not installed temperature controllers and experience the following symptoms, pleas

35 RESTARTING THE RINNAI WATER HEATER Following a power cut the heaters should be restarted in this manner. Standard system. Single or multiple wat

36 WIRING DIAGRAM MC-91-1A MC-91-1A

37 DIAGNOSTIC POINTS Diagnostic Points- To be read in conjunction with the wiring diagram.

38 SPECIFICATION Model………………………………………………..…...…………...Infinity 26i and HD50i Installation…………………………………………...………...……... Internal location only

39 SERVICE CONTACT Rinnai Rinnai UK LTD. 9 Christleton Court Manor Park Runcorn Cheshire WA7 1ST Tel. 01928 531870 Fax. 01928 531880 E-mail. i

4 UNPACKING RINNAI WATER HEATER • After unpacking the appliance check for damage, if the heater is damaged contact your supplier immediately. Do n

40 COMMISSIONING CHECK LIST

5 IMPORTANT INFORMATION 1. Gas safety (Installation & Use) regulations 1998 are the ‘Rules in force’. In your own interest and that of safety, i

6 General Installation Information. Internal Installations The Rinnai Infinity 26i and the Rinnai HD50i are for internal installation in conjunctio

7 General Information. The unit must be installed by a competent, authorised person. It is the installer’s responsibility to ensure that the unit

8 INSTALLATION INSTRUCTIONS - CONNECTIONS Water Supply. Where the water supply pressure exceeds 12 bar, an approved pressure reducing device is req

9 Dimension Terminal Position Distance A Directly below an opening, air brick, opening windows, etc. 300mm B Above an opening, air brick , openi